Nondestructive inspection of plasma-sprayed metallic coatings for coal conversion equipment
Read Online
Share

Nondestructive inspection of plasma-sprayed metallic coatings for coal conversion equipment

  • 982 Want to read
  • ·
  • 67 Currently reading

Published by Dept. of Energy, Oak Ridge National Laboratory, for sale by the National Technical Information Service] in Oak Ridge, Tenn, [Springfield, Va .
Written in English

Subjects:

  • Coal gasification -- Equipment and supplies,
  • Plasma spraying,
  • Nondestructive testing

Book details:

Edition Notes

StatementG. W. Scott, S. D. Snyder, and W. A. Simpson, Jr
SeriesORNL/TM ; 7090
ContributionsSnyder, S. D. joint author, Simpson, W. A., joint author, Oak Ridge National Laboratory
The Physical Object
Paginationiv, 63 p. :
Number of Pages63
ID Numbers
Open LibraryOL14881976M

Download Nondestructive inspection of plasma-sprayed metallic coatings for coal conversion equipment

PDF EPUB FB2 MOBI RTF

Download PDF: Sorry, we are unable to provide the full text but you may find it at the following location(s): (external link)Author: G.W. Scott, S.D. Snyder and W.A. Jr. Simpson. Infrared Thermography as a Non-destructive Testing Solution for Thermal Spray Metal Coatings Article in Journal of Thermal Spray Technology 26(8) September with Reads. Metallic Plasma Sprayed Coatings on Orthopedic Implants to Support Reconsideration of Postmarket Surveillance Requirements, dated Febru U.S. Department Of Health And Human Services. Protective Coating on Metallic Substrates • D Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs • D Evaluating Adhesion by Knife • D Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals.

5. ISO Measurement of coating thickness; Magnetic method 6. DVS Non-destructive testing of thermally sprayed coatings, thickness measurements 7. ISO Measurement of coating thickness; Eddy current method 8. ISO Paints and varnishes - Determination of film thickness 9. ISO Measurement of coating thickness; X-ray. C. V. Dodd's 68 research works with 1, citations and 1, reads, including: Eddy-Current Inversion of Flaw Data From Flat-Bottomed Holes. • Dense and protective coatings àCorrosion characteristics of the coatings are closer to Al bulk material than steel NACSC , Edmonton, Canada 20 H. Koivuluoto et al., Structure and propertiesof laser-assistedcold-sprayedAluminium coatings, MaterialsScience Forum, , , p. H. Xu, J. Wu, in Thermal Barrier Coatings, Plasma sprayed (PS) TBCs. In air plasma-sprayed (APS) coatings, inter-splat pores are roughly aligned parallel to the substrate surface and are accompanied by microcracks and a fine grain size. 84 This pore orientation is highly effective for impeding the flow of heat through the coating. Therefore, APS coatings have low thermal.

The deformation behavior of thermally sprayed partially stabilized zirconia (PSZ) coatings are investigated using Hertzian indentation and four-point bend testing, with in situ acoustic emission monitoring. The experimental deformation curves, together with the corresponding acoustic emission responses and the fracture properties of the material are used in defining the deformation. Traditionally, thermal barrier coatings (TBCs) are used in gas turbine engines to create an insulation layer between the metallic components and the gases in the hot section. Atmospheric plasma spray (APS) is a common method used to produce TBCs.   This chapter discusses the degradation issues for metallic equipment in hydrocarbon fuel conversion processes. Conversion processes cover a wide range of corrosive and fouling environments due to the different sources of fuel (crude oils, natural gas, coal, petcoke, lignin, tar sands, etc.) and a wide range of technologies (hydroconversion, cracking, oxidation, gasification, pyrolysis, etc.). AWS CXX, Specification for Thermal Spray Equipment Acceptance Inspection, WD-4, (19 pages). This standard specifies the thermal spray equipment acceptance requirements for plasma, arc-wire, flame-powder, -wire, -rod, and -cord, and high-velocity-oxygen-fuel (HVOF) equipment. The equipment supplier shall provide proof of.